Canopy Masks

View File 1/72 Hasegawa F-104 Canopy and Wheel Masks, .svg Format Uploading in the canopy mask in .svg Format Cheers, Hoops Submitter Hoops Submitted 10/03/2021 Category Canopy Masks

SR 71 Cockpit (.svg and .studio3) My first cockpit mask! For the Revell SR-71A in 1/48 scale. Include SVG and Silhouette Studio versions. I did not include inside masks since I am depicting the cockpit closed. You should be able to use the outside ones for inside as well. Note that rear cockpit windows appear too large if you include the OUTSIDE lines - so I matched against the inside lines. Finally corners were slightly rounded to match reference photos. Any feedback is appreciated! File Information Submitter Henrik Submitted 01/07/2026 Category Canopy Masks View File

Dragon/Revell Ju-188 Canopy masks 1/48 My first contribution, for the Revell/Dragon Junkers Ju-188 Rächer. File Information Submitter Bogus Submitted 11/18/2025 Category Canopy Masks View File

1/72 Scale Airfix New Tool Buccaneer Canopy Masks Canopy masks for the new tool Airfix Blackburn Buccaneer. Apply the first set of canopy masks before painting the light colored canopy seals. Then apply the second masks over those before painting the aircraft camouflage. The small circle is for the landing light on the nose landing gear. File Information Submitter Hoops Submitted 11/01/2025 Category Canopy Masks View File

Hs-123-WS General masks for ICM 1/32 Hs 123: will fit any boxing, as the plastic is the same in each case. Has been used on my model https://forum.largescaleplanes.com/index.php?/topic/103608-icm-hs-123-a-1/ File contains: Masks for windscreen - external only. One spare set provided. Note that as far as I can tell from photos, the outer edges of the windscreen were unframed, and only the lower frame and the central uprights need painting. If this is incorrect, please message me. Masks for main wheel centres. One spare pair provided. Masks for tail wheel centre. One spare pair provided. Mask for engine mount, part E7, so you don't paint over where the glue goes. …

1:32 - Fw 190D-9 Canopy - Early and Late Versionen Hello Here are two versions of the canopy - Early and Late Versionen - for the Fw 190D-9 in 1/32 scale. Have fun building! Harry File Information Submitter Timbacat Submitted 07/04/2025 Category Canopy Masks View File

View File Dreiecke - 5mm + 7mm; Dreiecke - 10mm + 14mm Hallo, hier ist ein Video zum abkleben von Flugzeugkanzeln. Hier habe ich einmal verschiedene Dreiecke erstellt, 5mm + 7mm und 10mm + 14mm. Länge Horizontal + Vertikal = 5mm bzw. 10mm, Länge Diagonal: = 7mm bzw. 14mm. Viel Spaß beim verwenden! Harry Submitter Timbacat Submitted 04/10/2025 Category Canopy Masks

View File P-47D Thunderbolt - 1/48 - Baldachin-Maske Hallo, hier ist eine Canopy-Mask für eine P-47D Thunderbolt für Hobby Boss - Kit. Die Maske kann auch für andere Hersteller verwendet werden, eventuell ist eine leichte Anpassung nötig Maßstab: 1/48 Viel Spaß beim verwenden! Harry Submitter Timbacat Submitted 04/08/2025 Category Canopy Masks

View File 1/72 Scale Hasegawa F-2A/B Canopy Masks This file has options for both the single and two seat canopies used on the kit, as well as a couple of other useful extras. See the attached image for which parts to use. Cheers! Hoops Submitter Hoops Submitted 03/20/2025 Category Canopy Masks

View File Canopy Mask - ICM 48323 - 1/48 - B-26G Marauder Canopy Mask - ICM 48323 - 1/48 - B-26G Marauder Layer 1 = Masken Layer 2 = Beschriftung Maßstab: 1/48 Viel Spaß beim bauen! Harry Submitter Timbacat Submitted 03/07/2025 Category Canopy Masks

View File Airfix Me 410A-1/U2 & U4 kit #A04066 Canopy masking for the two versions of the Me 410 by Airfix. Extra clear parts are on the clear parts tree but not designated in the instructions. Feedback always appreciated. Craig Submitter craig b Submitted 01/07/2024 Category Canopy Masks

View File 1/72 Scale Hobby Boss Rafale B Canopy Masks Also included are masks for the taxi lights on the nose landing gear, the landing light on the port wing root, the internal mid canopy windscreen, and the non skid areas on the fuselage next to the cockpit. Cheers! Hoops Submitter Hoops Submitted 01/10/2025 Category Canopy Masks

Halifax Canopy masks View File These two masks are for the Revell 1/72 Handley Page Halifax B Mk.I/II, GR.II. (kit number 04394) (may not be entirely accurate, BUT close enough for my tired old eyes...) I'm not too sure that I'll do any Turret masks for this kit as it will be a lot quicker just to cut out the masks using Tamiya Tape and a sharp exacto knife... Submitter DBB Submitted 06/18/2024 Category Canopy Masks  

View File Tamiya 300061095 - Masken für FockeWulf FW190 A8/R2 FockeWulf FW190 A8/R2 Schnittmuster wurden vom Original-Masking-Sheet nachgezeichnet und passen sehr gut. Da ich Neuling auf diesem Gebiet bin, möge man mir Fehler verzeihen. Beim ersten Versuch hat das Schneideprogramm Doppel-Linen gezeichnet und der Plotter hat dann 13 Minuten gebraucht zum plotten. 😞 Beim zweiten Versuch ist jetzt alles richtig. 🙂 Viel Spass beim bauen des Modells! Harry Submitter Timbacat Submitted 06/1…

View File Tamiya Bf109 E-4/7 canopy 1/48 Canopy masks for Tamiya Bf109 E-4/7, kit #61063. Appreciate any feedback. Submitter craig b Submitted 01/06/2024 Category Canopy Masks

Masks for the excellent new tool Hawker Hurricane. Please note that the outside masks have all been trial fitted and are accurate, the inside ones are simply a slightly reduced version of the outer but haven't been test fitted!

View File FineMolds 1/72 F-15 Single Seat svg File SVG file for folks using other other than Silhouette cutters, or who want to trace/cut manually. Silhouette Studio 3 file is here. Gene K Submitter GeneK Submitted 10/10/2023 Category Canopy Masks

View File FineMolds F-15J 72 scale v6.studio3 Canopy plus wheel/spares and Air Refueling masks for new (Sep 2023) FineMolds 1/72 F-15J (and other single seaters to be released (A, C, ...). I'll post two seater masks after kits are released (Dec 2023). SVG file is here for folks who have other than SIlhouette cutter. Gene K Submitter GeneK Submitted 10/10/2023 Category Canopy Ma…

View File Hawker Hunter F5 canopy Canopy masks, inside and out for the Hawker Hunter. The masks were produced specifically for the Echelon Vac form kit, comparisons with the Revell Hunter show that the latter canopy is slightly wider than the Echelon so if used, these masks may need a bit of tweaking. Submitter Mozart Submitted 08/26/2023 Category Canopy Masks

View File Hawker Hurricane Revell new tool Masks as described, outer test fitted and accurate, inner ones are a reduced version of the outer but not test fitted.....over to you. 😄 Submitter Mozart Submitted 01/23/2023 Category Canopy Masks

View File Avro Anson (early) all frame masks Complements the late upright version. Submitter Mozart Submitted 12/25/2022 Category Canopy Masks

View File Avro Anson windscreen (late) mask Drawn in 1/48 scale for the new Airfix kit, inside and outside masks. Max Submitter Mozart Submitted 12/13/2022 Category Canopy Masks

View File TM-Windscreen-324872.studio3 I've been working on a pair of ICM Tiger Moths, and in common with many ICM kits, there is a mask template in the instructions which was easily used to produce these masks. I thought that as we have recent kits of this from Airfix in both 1/48 and 1/72, I'd include these by downscaling the 1/32 masks as detailed in a note on the file. There is also a separate set of drawings off the cutting area: these are there as an indicator of which mask is which, they correspond to the ICM instructions, thus they are not guaranteed to be the same size as the final masks on the cutting area. I am in t…

Hawker Hunter T7 (Fisher conversion) View File After a little nudge from Mike C., I've tweaked my rather indifferent first attempts at canopy masks for the Fisher Hunter T7. It's not an easy mask designing project due a) to the shape of the canopies b) the not too good definition on my canopy between glass and metal framing and c) a slight inconsistency in size for the canopy sections ie left and right of the main canopy and matching sections of the front. So using these masks comes with a caveat: they fit well but not perfectly so on the front ones especially you will need a fresh blade in your scalpel to make small adjustments! …

as stated above needed